Multi-channel power amplifier. 50W x 8 into 8ohm and 70W x 8 into 4ohm. Bridge configuration possible with power of 140W x 4 into 4 ohm. High current transistor class A/B power amplifier. Toroidal transformer. Selected components. Tone controls. 4 stereo or 8 mono RCA inputs configurable with internal matrix. PA announcements on each zone simultaneously. Phoenix type speaker output terminals. 12V Trigger. IP/RS232. 2U rack mounting brackets included. LCD front display.
Multi-channel power amplifier. 50W x 8 into 8ohm and 70W x 8 into 4ohm. Bridge configuration possible with power of 140W x 4 into 4 ohm. High current transistor class A/B power amplifier. Toroidal transformer. Selected components. Tone controls. 4 stereo or 8 mono RCA inputs configurable with internal matrix. PA announcements on each zone simultaneously. Phoenix type speaker output terminals. 12V Trigger. IP/RS232. 2U rack mounting brackets included. LCD front display.
Based on 36 reviews
Secure and verified payments
Paypal, credit card, bank transfer
Guaranteed Products
Buy new products, with original packaging and covered by warranty.
Our experts
We offer you maximum availability by phone and by email.
After-sales assistance
We are always at your disposal, even after the purchase.
The Rotel C8 Custom Installation Amplifier benefits from 60 years of audio engineering in terms of performance, sound quality and lasting value.
The C8 delivers 70 Watts of Class AB power to 8 discrete channels and into a 4 ohm connected load. The 8 channels can also be bridged for a total power of 140 Watts for 4 channels.
It uses a custom made oversized toroidal transformer that drives high current output transistors, fed by a series of storage and filter capacitors, which guarantee deep, fast and controlled bass, with all musical genres.
The C8 has 4 analog inputs that can be routed to each of the 8 zones with an internal matrix switching system, in addition to the PA mute function, which allows instantaneous announcements to be sent to all zones.
The display and push-button controls on the front panel allow input selection, independent setting of volume, bass and treble for each zone, ensuring maximum flexibility of configuration, based on listening preferences, speakers used and room characteristics. The complete setup is also available remotely via IP/RS232, so it can be controlled and configured even if installed in racks or in technical cabinets that are difficult to reach. The 12 Volt trigger control allows for both remote on and off switching.
The speaker terminals are removable Phoenix type with safety catches, allowing for pre-wired, non-reverseable installations.
The 2U chassis is designed to be custom rack-mounted, with no upper or lower space required for ventilation. All rack mounting hardware is included with the amplifier.
SPECIFICATIONS
Maximum output power: 70 W/ch (8 channels driven, 4 Ω)
Continuous output power: 50 W/ch (8 channels driven, 8 Ω)
Bridged output power: 140 W/ch (4 channels driven, 4 Ω)
Total harmonic distortion: < 0.1%
Intermodulation distortion: < 0.1% (60 Hz : 7kHz, 4:1)
Frequency Response: Line Inputs 10 Hz - 100k Hz, 0 ± 0.5 dB
Tone Controls: Bass ± 10 dB at 100 Hz Treble ± 10 dB at 10k Hz
Damping Factor: 80 (20 Hz - 20 kHz, 8 ohms)
Input Impedance/Sensitivity: Line Inputs (RCA) 0.3 V / 31k Ω
Input Overload Level: Line Inputs (RCA) 2.8 V
Signal-to-Noise Ratio (IHF "A" weighted): Line Inputs 100 dB
Crosstalk/Separation: > 50 dB
Power supply: 230 V, 50 Hz
Power consumption: 570 W
Standby consumption: Normal < 0.5 W Network standby < 2 W
BTU (4 Ω, 1/8 of rated power): 1537 BTU/h
Dimensions (W×H×D): 430x97x414 mm
Front panel height: 2U / 88.1 mm
Net weight: 16.7 kg
Data sheet
English
Italiano
Français
Deutsch
Español
